Serving the Greater Orlando area since 2003.
Serving the Greater Orlando area since 2003.
Bring us your chlorine pump.
We will service it in our shop. Most chlorine pumps can be repaired or rebuilt.
Call for details 407-323-9010 repairs for chlorine pump repairs to stenner water treatment equipment Oviedo Orlando Sorrento
Bring us your tanks or have us come to your site and do all the work.
We offer refurbished filter and softener tanks on an exchange basis.
We clean and inspect the tank, then we install the new media and distributor tube. We coat the tank with enamel paint for protection from weather.
Filter, Carbon 10″ diameter 54″ height: $240.00
Softener 10″ diameter 54″ height: $295.00
Core Charge for Tank: $75.00
Exchange your re-usable tank, Subject to inspection. Prices are in the store only.
Call for details 407-323-90104 water treatment equipment
We offer refurbished filter and softener tanks.
We come to you and exchange the tanks.
In our shop we clean and inspect the tank, then we install the new media and distributor tube. We coat the tank with enamel paint for protection from weather.
Filter, Carbon 10 x 54 $240.00
Softener 10 x 54 $295.00
Your tank must be usable condition for us to recondition it. If not, additional charges will apply. water treatment equipment Orlando
Most water softener and filter controllers can be repaired or rebuilt on site.
Most chlorine pumps can be repaired or rebuilt on site. Call for details
Most of the water treatment happens here. There are no shortcuts.
This tank is plumbed downstream of the well or source water and upstream of the carbon filter. Chlorine is injected at the inlet where it mixes with the water prior to entering the tank. The inlet is located at the bottom of the tank. The chlorine reacts with the water. The water exits the tank through the top. From there the water goes the carbon filter for dechlorination and particle removal.
Chlorine does three things:
1-it kills bacteria. Chlorine takes 15 minutes to kill bacteria. This tank is sized at 120 gallons. At 8 gallons per minute flow rate, you will get 15 minutes of retention time.
2-it oxidizes iron. The iron will turn to rust and settle to the bottom of the tank.
3-it oxidizes sulfur. The hydrogen sulfide (H2S) gas in the water is the source of the rotten egg odor in the water. The oxidized sulfur becomes a solid and it settles to the bottom of the tank.
There is a drain at the bottom of the tank. Open it periodically to flush the settled solids out. Solids do not settle perfectly. Often they will stick to the side of the tank. The most effective way to flush them out is to empty the tank. Allow air to enter the tank from the spigot near the top as you drain it. Open the inlet and allow water to flow in while the drain is still open. This will allow the tank to be cleaned more thoroughly. Run the water until it appears clear. Allow air to escape out the spigot near the top when refilling the tank.
Brand Flex-Lite Model FLU-120 Warranty 5 Years Dimensions 24" Diameter 72" Tall Capacity 120 Gallons Pressure Rating 125 Psi Temperature Rating 120 Degrees Fahrenheit Retention Time 15 Minutes At 8 Gallons Per Minute
Shipping Weight 70 Lbs. Weight When Full 1,080 Lbs.
Mount on solid concrete floor or pad. Floor must be level. As with all fiberglass tanks, a vacuum relief must be installed to protect the liner against damage in the event of a vacuum condition forming inside the system.
Follow the manufacturer's instructions for installation
Tank $649.00 in the store. Plus tax. Installation is available in our service area at additional cost. Contact us for details.
WE DO NOT "SHIP' THIS TANK.
A pressure tank stores energy in the form of compressed air. The well pump puts water into the pressure tank. The air that is stored in the pressure tanks bladder becomes compressed. When water is used, such as opening a faucet in the house, the compressed air forces the water out of the tank. The well pumps primary job is to fill this tank. The pressure tanks job is to supply your home with water. The tank must be properly sized and properly maintained so that the well pump does not start too frequently.
Maintenance: At least every three months check the air pressure in the tank. Add air according the the manufacturer’s instructions.
Method: Turn off well pump. Open a spigot to relieve water pressure to zero psi. Use a pressure gauge, such as the type used to check tire pressure, to read air pressure at the schrader valve on top of the tank. The pressure reading should be 4 psi below pump cut on pressure. For example, if the well pump turns on at 30 psi, the pressure tank should have 26 psi of air in the tank. If the pressure is lower than required, add air with an air compressor.
These are general instructions. Consult your tank's instructions for maintenance details. Failure to maintain air pressure may result in damage to the bladder and will surely result in short-cycling of the pump. Short cycling is a condition in which the well pump starts too frequently. Short cycling will result in higher energy consumption and a shortened life expectancy of the pump and control devices.
35 GALLON MODEL FL-12
50 GALLON MODEL FL-17
90 GALLON MODEL FL-30
All prices are plus tax, in the store. Installation is available in our service area.
Contact us for details.
WE DO NOT "SHIP' THESE TANKS.
Monthly Service Contracts available in limited area.
Notice to consumer: Operational, maintenance, and replacement requirements are essential for all water treatment devices to perform as sold.
Copyright © 2019 DISCOUNT WATER SUPPLY INC